TPMS display in ColorMFA

[Schattenwelt]

Hello is it possible to display the pressure of each wheel in ColorMFA?

[autopilot]

No. Currently this feature is not present. Because all of TPMS for supported cars does not support this feature.

[Schattenwelt]

How are the messages displayed? Just like in the original with red, yellow and position related or just general?

[autopilot]

Work same as on original mono screen.
Warnings:
- Check tire pressure ! (without indicating the position)
- Tire pressure monitor system failure !

In menu present some controls as on original screen (on/off, store pressure)

cb34e619d495d34e948f389077a51908.jpg

48_save.jpg

[Schattenwelt]

Is it possible to allow the position with displays? I can help too. I have retrofitted this in my Passat 5.5

[autopilot]

What car did you install the TPMS module from ?

[Schattenwelt]

From an Audi A8 D2.

[autopilot]

I do not know how to work TPMS from A8D2.
Supported TPMS from A6C5 and A48E.

[Schattenwelt]

RDKS ist das gleiche wie im Audi A6C5.

[autopilot]

TPMS menu displayed in ColorMFA ? Works correctly (on/off TPMS, save pressure) ?
Please take photo of CAN-monitor screen with enabled only Comfort-CAN.
Need see lines beginning from 341, 641 and 441 (if present).
CAN-monitor screen can be scrolled with "up" and "down" buttons.

[Schattenwelt]

Yes the point is displayed and also the memory works. But it only shows that it has pressure loss but not on which wheel.

IMG_20200205_144824-min.jpg

1.jpg

2.jpg

3.jpg

[autopilot]

I think is possible to show wheel position while error on this system. Also may be possible to show pressure on screen for each wheel.
Please do this:
1. Run diagnostics from PC (not from ColorMFA). Connect to TPMS -> Measure blocks -> Select any block (group) where showed pressure and temperature info for wheel (any wheel). Take photo of screen. Also in same time run CAN-monitor with Comfort-CAN only and take photo of screen.
2. Generate error on any wheel (blow off any wheel) and take photo of CAN-monitor screen with only Comfort-CAN. Also say in what wheel this error is generated.

[Schattenwelt]

This is the data for Error.

Error-min.jpg

Error1.jpg

Error2.jpg

Error3.jpg

[Schattenwelt]

Okay, this is the regular.

OK-min.jpg

OK1.jpg

OK2.jpg

OK3.jpg

[autopilot]

Thanks. I'll try to add this function. But I don't see any mismatches on CAN-bus. I see only global error about wheels, but not see low value in any of wheel.
You did photo in VCDS and CAN-monitor in same time ? Error generated in front right wheel ?

[Schattenwelt]

Yes front right. However, it may only be a general mistake because it is a rapid loss of pressure. I have to read the instructions again. Yes it was at the same time.

[Mario]

Is it posible to retrofit TPMS in S3 8L? Will colormfa in s3 8L recognize and comunicate with tpms module from a6 C5?

[autopilot]

All firmwares for ColorMFA (except B5 immo2) support this function.

[Schattenwelt]

Hello I got the message today to check the print on the front left. But when I click on the main message Path I have no symbol in the status bar and there is nothing in the messages. If I turn off the ignition for a short time, the symbol in the status bar appears for 5 seconds and then goes off again. But it is also only the "yellow" message.

1-min.jpg

2-min.jpg

3-min.jpg

[autopilot]

You did not tell me about the work of all changes in the firmware. Does temperature and pressure display work ? Main warnings tested ?

I think the original warning worked like that. In the photo there are no warnings in the data on the CAN-bus.
I checked the work on the original screen. A original message disappears from the screen within 2 seconds after it disappeared on the CAN-bus. ColorMFA works the same. If warning or error disappeared on the CAN, it also disappeared from screen.